|
|
||||||||||||||||||||
What' new in
GeoTools V10: GeoTools V10 is the first version of GeoTools to be compatible with AutoCAD 2010.
New commands added in GeoTools V10 GT_CONNECTBLOCKS command: GeoTools -> Blöcke Tools-> Bitte Blocks verbinden,basiert auf Attributwerten GT_DRAWSEGBLOCKS
command: GeoTools ->
Blöcke Tools-> Bitte gestreckte Blocks Lineare Segmente entlang Legen GT_ATTROTATE
command: GeoTools -> Blöcke Tools-> Attribut umkehren GT_ATT2XD command: GeoTools -> Konvertierung Tools-> Attribute to Xdata GT_WBLOCKBC command: GeoTools -> Diverse Tools-> Wblock and preserve AutoCAD Map objects GT_FILTER command: GeoTools -> Auswahl Tools-> Objektselektion Filter GT_APPLOAD command : GeoTools -> Diverse Tools -> Anwendungs Loader mit Startgruppe GT_LENTEXT command: GeoTools -> Beschriftungs Tools-> Erzeugen/aktuallisieren Länge annotation GT_TRIANGULATE command: GeoTools ->Bauwesen Tools-> Unregelmäßiges Dreiecksnetz erzeugen (Delauney triangulation) GT_TAGDEL command: GeoTools -> Blöcke Tools-> Blockattributtags von der Blockdefinition entfernen GT_TORIENT command: GeoTools -> Text Tools -> Text Orient: Text machen, MText lesbar GT_TRAVADJ command: GeoTools -> Bauwesen Tools -> Durchführen der Polylinienausgleichung GT_TABLEEDIT command: GeoTools -> Diverse Tools -> TABLE Edit / Explode, Bricscad only GT_CONVERTPOLY command: GeoTools -> Konvertierung Tools -> Polylinien nach LW-Polylinien GT_EASYATT command: GeoTools -> Blöcke Tools -> Leichte multiple choice atttribut redacteur GT_EASYATT_SETUP command: GeoTools -> Blöcke Tools -> Leichte multiple choice atttribut redacteur Einrichtung GT_EASYOD command: GeoTools -> AutoCAD Map Tools -> Leichte Multiple-choice, object data Redacteur GT_EASYOD_SETUP command: GeoTools -> AutoCAD Map Tools -> Leichte Multiple-choice, object data Redacteur Einrichtung
Commands Enhanced or changed GT_CONTLABEL [ Annotation Tools -> Label contour polylines ] : The GT_CONTLABEL command had an option in the user-interface to hode the contour line under the text with a WIPEOUT object but this option was greyed out and not functional. This has now been made operational. GT_3DOFFSET : ( Build Tools -> Offset 3d polylines) : The GT_3DOFFSET command has been significantly enhanced. You can now offset a 3d polyline on both sides (at once) as well as specify the layer into which the offsetted polyline must go. The ability to perform a 'Both Sides' offset significantly cuts down drafting time for civil/survey/map users who use this tool to create roadways, corridors and 3d ramps etc. In layer settings, it is now possible to create offset polylines either in the Current, Source or specific layers. GT_MVMEASURE : (Build Tools ->
Multiple-Variable measure) : The GT_MVMEASURE command now has its own
scale factor GT_REPBLK : (Blocks Tools -> Replace Block) : The operation of the 'Select Manual' method has been changed slighlty. Instead of offering an option to choose the layer name(s) first, the program now offers a 'Select objects' prompt first. If no objects are selected, the option to filter by layer name(s) is offered next. This change has been effected to make the process of selection more intuitive. GT_XV: (Polyline Toolset 2 -> Express
Pedit) : GT_XV : (Polyline ToolSet 2 -> Express Pedit) : Two
new enhancements have been made in the way the Z values for vertices
are set. You can now acquire Z values by picking neighboring text
objects or by picking an existing point or 3d feature to use its Z as
the vertex elevation. These two additions can be specified via the
SEttings sub-option of the GT_XV command, in addition to the old method
of explicitly keying in a Z value for vertex. GT_SEGLABEL : (Annotation Tools -> Annotate Segment Labels) : A new option has been added to perform Slope annotation. It is called 'Per Mille', which translates into 'Per 1000'. It is often used in hydraulics to denote the slopes of canal beds and similar structures. Additionally, you can now specify an exaggeration factor to use when you are annotation polylines which are in Elevation View. So, if your 'Elevation View' polyline is already exxagerated 10 times in Z, you should apply a reversal exageration factor of 0.1 while doing GT_SEGLABEL to get the correct slope figures. GT_IMPEX : (Export Tools -> Import/Export points and lines): This command has been enhanced. A new 'Multiple Descriptions Import' capability has been added which makes it possible for text files containing additional description data to be imported into the drawing as attributes, object data or plain text. Until now, only one description field was possible via the format descriptor PENZD,.. etc. Now, you can bring in as many and all of the descriptions into the DWG GT_DELVX : (Polyline
ToolSet 1 -> Delete Vertex) : An 'X' (Exit) option has been added to
this command to gracefully exit without having to bail out of the
command using the ESC key.
Interface changes
----
Bug Fixes In the GT_BLKEDIT command, the SlideX and SlideY options were not working correctly when the text had middle and right justifications. This has been corrected. GT_ISOD [Layer Tools ->
Isolate Layer(s)] & GT_RESTORE [Layer Tools -> Restore Isolated
layer(s)]: Both these commands caused a crash in AutoCAD 2009 and 2010.
This has now been fixed.
GeoTools Tutorial |
||||||||||||||||||||
